Blue Mountains, NSW - 2020 - Hike 1

Echo Point loop via Giant Stairway, Jamison Valley (Federal Pass) and Furber Steps


Distance: 9.62km



The walk began with the rapid descent into the Jamison Valley via the aptly named Giant Stairway. The pictures below highlight some of the many, many steps:







After clearing the last of the stairs, the path continues within the cool climate rainforest environment that thrives in the valley.





Katoomba Cascades

As I re-emerged from the valley, the weather had started to change, with light showers and cloud rolling in.







With a little under an hour to go in the loop, the cloud had well and truly taken over and there wasn't much scenery to see:






The Elevation Profile illustrates just what an up-and-down route this is:




All in all, a lovely walk. I took it mid-week, which I'd recommend as weekends have a reputation for being rather busy.

Location: 33/37 Echo Point Rd, Katoomba NSW 2780, Australia

Comments

Post a Comment

Popular posts from this blog

Change the ComputerName value in Unattend.xml using PowerShell

A quick and dirty PowerShell script to update the value of ComputerName in Unattend.xml before imaging. This particular value is located at: <unattend>  <settings pass="generalize">   <component name="Microsoft-Windows-Shell-Setup" processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">     <computername> Which is a bit of a mouthful, but we can be lazy and just pull the value from the nth component node (in my case it's 3, or the 4th component node). PowerShell uses dots to describe the hierarchical path, which looks a lot neater than the above: $xml.unattend.settings.component[3].computername To repeat, the value of .component[n] will change depending on the structure of the file. The value of the...
Read more

Testing out Link Aggregation

Image
I picked up a TP-Link managed switch last week as something of a compromise between affordability and features - as it turns out though, it does just about everything I could ask for, just without the extra expense from buying something that has HP or Cisco written on the side. I grabbed the TL-SG3216, a fanless L2 managed switch with 16x1Gigabit ports as it ticked all the boxes: Silent (fanless) Managed Link Aggregation/802.3ad (LACP) 802.1Q (VLAN) STP As a bonus, the CLI interface (via console cable or ssh) is very similar to Cisco's IOS, so I don't have to learn an entirely new syntax to configure it. Before I replace my existing switch, I spent a bit of time testing out its features. First up, I setup a spare Raspberry Pi with a second ethernet interface (via a USB dongle) to test out link aggregation. First up, the configuration on the Pi (Raspbian): Install ifenslave to allow for the creation of bonded network interfaces # apt-get install ifenslav...
Read more

Adding 802.1Q Trunking to Debian GNU/Linux

Here's a quick guide to setting up 802.1Q trunking for VLANs on a Debian GNU/Linux box connected to one or more Cisco Catalyst switches, which could then be used as a cheap router replacement. Configuration on the Debian box: Add 8021q to /etc/modules so 802.1Q support is enabled at startup. To install it immediately: # modprobe 8021q Use vconfig to add the VLANs to the interface you'll be using (if vconfig is missing, run apt-get install vlan ): # vconfig add eth0 2 (In the above, eth0 is the physical interface and 2 is the ID of the VLAN) Give the interface an IP. Choose an address in the range you've set aside for that particular VLAN. In this example, VLAN 2 is using 192.168.2.0/24. # ifconfig eth0.2 192.168.2.201 netmask 255.255.255.0
Read more